Electia Home Prosafe Sc9100 Instrukcja Użytkownika Pobierz pdf (Strona 13)

Advanced security functionsAdvanced security functions

Disarming the siren for silent alarm

You can set the security system to raise the alarm without sounding the siren (just the telephone dialler and

lighting). In case of a burglary, the built-in siren will not be activated (N.B., Other sirens installed will still work). The

siren is turned on in the factory settings.

1. To access the menu, press the menu upp or menu down button. The display now shows ENTER PIN.

2. Enter your 4-digit PIN code (factory setting 0000). For every digit entered, a * will appear.

3. When the PIN code has been entered correctly, the word INSTALL will show up on the display.

4. Use the menu buttons upp or down to go back to menu item 7. OPTIONS- Press OK to select this menu item.

You can also go to this menu item directly by pressing a 7 on the number pad.

5. Use the menu buttons upp or down to go to menu item SIREN- Press OK to select this menu item.

6. Choose 1 for SIREN ON or 2 for SIREN OFF.

7. Press CLEAR again to quit the menu. To confirm your choise, press 1 for Yes or 2 for No. If you choose Yes,

you will quit the menu. If you choose No, you go back to the first menu item.

Activating the chime

The console can, when in DISARMED mode, sound a chime - ding-dong- when a door armed with a Door/Window

sensor is openend. This ensures that you will always hear if someone is entering your house or small children

open a door. This function is activated in the factory settings.

1. To access the menu, press the menu upp or menu down button. The display now shows ENTER PIN.

2. Enter your 4-digit PIN code (factory setting 0000). For every digit entered a * will appear.

3. When the PIN code has been entered correctly, the word INSTALL will show up on the display.

4. Use the menu buttons upp or down to go to menu item 7. OPTIONS. Press OK to select this menu item.

You can also go to this menu item directly by pressing a 7 on the number pad.

5. Use the menu bottons upp or down to go to menu item CHIME. Press OK to select this menu item.

6. Choose 1 for CHIME ON or 2 for CHIME OFF.

7. Press CLEAR again to quit the menu. To confirm your choice, press 1 for Yes or 2 for No. If you choose Yes,

you will quit the menu. If you choose No, you go back to the first menu item.

8. If you see a note (music) on the display, the chime is activated.

The chime function also works for the wired inputs on zones 31 and 32.

Using wired inputs

The console has two inputs for wired sensors. These sensors need to be of type NC (Normally /closed contacts).

There should not be any power on these inputs (ptential-free /dry).

Connecting a wired sensor.

1. Open the top compartment on your console.

2. You will see two wired inputs.

3. Remove the wire bridge and connect your wired sensor.

4. Close the top compartment of your console and enter your PIN code to remove the word TAMPER from the

display.

5. The wired sensor is now ready for use.

Adding a wired sensor to the Door/Window sensor Ds18.

The Ds18 Door/Window sensor has a contact for an extra wired sensor. These sensors need to be of type NC

(normally closed contacts). There should not ba any power on this contact (potenyial-free). A few examples:

Securing a window with multiple magnetic contacts.

Adding extra sensors to your system, e.g smoke detectors, temperature sensors, sensors to detect electrical

failures etc.

1. Open the transmitter part of the Ds18 by taking the two parts apart.

2. Remove the wire bridge from the connection for the wired sensor.

3. Connect the wired sensor.

The wired contact has its own Zone on the Base Console. You can register the contact using the procedure (to

Deregistering a Door/Window or Motion Sensor.

1. To access the menu press themenu upp or menu down button. The display now shows ENTER PIN.

2. Enter your 4-digit PIN code (factory setting 0000 se page 12 for changing the PIN code)

3. When the PIN code has been entered correctly, the word INSTALL will show up on the display.

4. Press OK.

5. Enter the number of the zone you want to earse on the number pad and press CLEAR.

6. You are asked to confirm CLEAR ZONE 1. Yes 2. No.

7. Press 1 to erase the zone. The zone number is shown on the display.

8. Press CLEAR again to quit the menu.

Zones 31 and 32 can not be erased.

1 2 ... 8 9 10 11 12 13 14 15 16

Komentarze do niniejszej Instrukcji

Brak uwag

Electia Home Prosafe Sc9100 Instrukcja Użytkownika Strona 13

Komentarze do niniejszej Instrukcji

Powiązane produkty i podręczniki dla Systemy kontroli dostępu bezpieczeństwa Electia Home Prosafe Sc9100